Techlog软件WBI培训
发布时间:2019-10-27 00:17:25
发布时间:2019-10-27 00:17:25
WBI培训
Module 1:Data Loading
1. Import✍F4✍Parameters✍Script to be lauched=Techlog\WbiImport
2. IMAGE-WELL2_RAW.dlis
3. Import dataset=FMI_16_1271-1501m
Module 2:Data Processing
4. Image processing wizard
5. Input data: Top=1721.4m, Bottom=1500.4m
6. 产生FMI Processing workflow
Inclinometry QC
7. Inclinometry QC
8. Inclinometry method parameters:
Geomagnetic Components tab: 即处理向导中输入的参数
Processing tab: 4种处理方法。根据Geomagnetic Components tab参数对测井得到的magnetometer 磁场和 accelerometer 加速度曲线进行刻度,算出其偏移和增益,并显示在其左边的Offsets and Gains tab中。然后利用这些偏移和增益对测量的magnetometer 磁场和 accelerometer 加速度曲线进行校正,继而重新计算新井斜数据。
Offsets and Gains tab:(manual法时为人工输入)
Offsets tab:Measure Point Offset,Angular Offset:(人工输入)
结果:校正前后数据对比,绿色表示合格,红色表示误差超限。
右边交会图:黑点为校正前点子,绿点为校正后点子。中间红点为Ax, Ay, Fx, Fy偏移校正量。
9. Continue without saving
Speed correction
10. Cable confidence factor: 允许0-10,隐含3,越高加速度变化对测井深度的影响越小。
11. Sticking detection threshold: 遇卡加速度门槛值,小于它,表示仪器遇卡。
12. Recovery speed: 仪器解卡后速度恢复的快慢程度,越高,越快。
13. Next
Processing
14. Pad image creation
15. Image-based speed correction (相邻电极/极板图像深度微调)
16. Button harmonization: Window size for harmonization 最大地层角度对应正弦线高度的三倍,且>=15ft 或>=5m
17. Next
18. Next
Create static image
19. Deviation 0-30 degrees: Wireline images usually oriented to North
30-45 degrees: North or top of hole according to preference
45-60 degrees: Should be oriented to Top of hole, but orientation to North can be ok
> 60 degrees: Must be oriented to Top of hole
20. Next
21. Next
Create dynamic image
22. Deviation 0-30 degrees: Wireline images usually oriented to North
30-45 degrees: North or top of hole according to preference
45-60 degrees: Should be oriented to Top of hole, but orientation to North can be ok
> 60 degrees: Must be oriented to Top of hole
23. Next
24. Next
25. Finish
26. Save the workflow
Module 3:Image Display in LogView
27. Display FMI_STAT, FMI_DYNA in Logview by drag&drop
28. F4✍Limits✍Orientation✍Default value=90
29. Processing✍Gaussian smooth or Average smooth
Module 4:LWD Image Handling
30. Import
31. IMAGE-WELL5-LWDIMG.dlis
32. WBI✍Processing✍LWD Image Preparation
33. Service Company=SLB
34. OK
35. OK
36. Ok
37. Ok
Module 5:Dip Picking
38. 打开保存的IMAGE-WELL2图
39. 选择两个image,点击右键✍Create a dip variable
40. Advanced✍Dip classification✍Bedding✍解释一个蝌蚪✍点击右键确定
41. Advanced✍Dip classification✍定义自己的蝌蚪类型
42. 使用正弦线✍按住左键上下移动可改变正弦线高度✍松开左键(什么键都不按)左右移动,可移动正弦线位置✍点击右键确定
43. 把鼠标放在一个正弦线(或蝌蚪)的上方,光标变成十字架时,按住并上下左右移动,可修改正弦线位置。
44. 把鼠标放在一个正弦线的上方,光标变成十字架时,按住shift键时,点击左键可修改正弦线上的点。
45. 把鼠标放在一个正弦线(或蝌蚪)的上方,光标变成十字架时,按delete键可删除该正弦线或蝌蚪。
46. 局部特征解释
47. 井眼崩落解释
48. 诱导缝解释
49. Save the modified variables
50. Close the Logview
51. Re-open the Logview
52. Display the dips as sticks in a new track
Module 7:Automatic Dip Computation
53. Dips handling✍Automatic dip computation
54. CPL-Tuha LU 1STAR相关对比计算倾角:
仪器选择6 ARMS_DIPMETER、Family选择、对应曲线,我试验了,可以处理,但不要这样处理,因为6臂曲线未进行加速度校正。继续看后面。
请这样处理。仪器选择STAR、Family选择、对应曲线。
55. Insert✍Borehole Shape✍
56. Click unknown✍F4✍Display option✍Area fill array✍Activate=Yes✍Name=FMI_STAT✍threshold(pixel)=1
Module 9:Fracture analysis
57. LLS=1000/MEAN, RM=MEAN*0+0.2 (或加载IMAGE-WELL2-LLS_RM.las文件得到。加载时直接选中这两条曲线进行Import)
58. Processing✍Image calibration✍save and display✍edit calibration✍apply calibration
59. 解释Conductive fractures或直接使用加载的DIPS-FINAL数据集中的Conductive fracture。请打开一个空白的LogView窗口,把DIPS-FINAL数据集中的Dip_TRU拖入其中,将显示如下图所示的所有类型的蝌蚪点。该井中的Dip数据集为我解释的与加载的DIPS-FINAL合并后的结果。
60. 如何只显示裂缝蝌蚪点。按F4,改显示属性。
61. 新起一个工作流程,命名为IMGCAL_FVA(你命名成啥都可以,这里是图像刻度加裂缝宽度计算的意思)。过程如下:Geology✍Processing✍Image calibration✍Create:
62. 把FMI_16_1271-1501m数据集拖入其中,选择4个主极板和4个副极板。
63. 用隐含参数运行得到下图。本练习使用的LLS并不是真正的LLS测井曲线,而是用成像所有纽扣电极电阻率的平均值,所以两者关系特好。在实际处理中,你可以按照实际的数据关系趋势移动和删除红点。
64. 把该计算(Image Calibration)的输出曲线组名改为IMGCAL,曲线后缀改为_IMGCAL,运行模式改为save and display。运行得到:
65. 把参数表中的Apply mode由edit calibration改为apply calibration,运行得到刻度过的极板图像。
66. Geology✍Dips handling✍Fracture aperture,按Create
67. 参数表:Dataset选FMI_16_1271-1501m✍用其中刻度过的图像,Dip Dataset选DIPS- FINAL✍用其中的高导裂缝蝌蚪数据。
)
68. 运行后计算的三条裂缝宽度曲线将放在DIPS- FINAL数据集中。
69. 新起一个工作流程,命名为DFC(你命名成啥都可以,这里是Dip feature counting的意思,即计算裂缝密度、长度、孔隙度)。
70. Geology✍Dips handling✍Dip feature counting, 按Create。一定要在一个新的流程里加Dip feature counting。不要把它加在裂缝宽度计算的后面,因为他们用数据集不一样。
71. Inputs选择如下,注意Dip Type=Type。
72. 参数表。注意Feature to count只选Conductive fracture。
73. F4✍Output variables(该方法输出曲线选择。将新产生一个数据集,名称是蝌蚪数据集名加后缀_DFC。曲线组名为DipFreatureCounting)。
74. 运行得到裂缝密度、长度和孔隙度结果。如下图:
曲线名称解释:
75. COUNT:统计窗口裂缝个数
76. P10(=COUNT/统计窗口长度=发育密度1/m)
77. P10_C:裂缝面与井轴夹角校正后的发育密度
78. P21(裂缝长度m/m2=1/m)
79. P32(单位井眼体积内裂缝面面积)
80. P33(裂缝孔隙度v/v)
81. _trace: The _TRACE suffix in a variable means that the fracture trace in the borehole wall was computed from the fracture aperture variable (that is to say it only includes the parts of the fracture trace that have a detectable aperture). 带trace的按裂缝实际的、断续的长度计算(不按理论的连续的正弦线计算)
82. 不带trace的按理论的、连续的正弦线计算
83. 把第一个流程保存为IMGCAL_FVA
84. 把第二个流程保存为DFC
85. 把整个workflow manager
保存为IMGCAL_FVA_DFC,如右图:
3DV显示
86. Utility✍3D Vue
87. 打开菜单条和左侧部分窗口
88. 把FMI_STAT_Img拖入左侧窗口中
89. 把开始深度改为1300
90. 限定在实际范围(选中左侧窗口中图像数据,按右键,并选择Go to the cover box of IMAGE-WELL2)
91. 改X,Y方向框框大小
92. 把Dip_TRU拖入左侧窗口中
93. 选中Dip_TRU,按F4键修改要显示哪些蝌蚪
94.